8-speed automatic gearbox 0D6

Chapter overview

• Technical data
  1
• 1 Identification
  1
• 1.1 Gearbox identification
  1
• 2 Safety information
  2
• 2.1 Safety precautions when working on the vehicle
  2
• 2.2 Safety measures when working on vehicles with a start/stop system
  3
• 2.4 Safety precautions when tow-starting or towing
  3
• 3 Repair instructions
  4
• 3.1 Rules for cleanliness
  4
• 3.2 General information
  4
• 3.3 General repair instructions
  5
• 3.4 Routing and attachment of lines
  7
• 4 Technical data
  8
• 4.1 Allocation gearbox - engine
  8
• 4.2 Capacities
  8
• 5 Overview - power transmission
  10
• Torque converter
  11
• 1 Torque converter
  11
• 1.1 Assembly overview - torque converter
  11
• 1.2 Removing and installing torque converter
  11
• 1.3 Draining torque converter
  14
• 1.4 Checking torque converter
  15
• 1.5 Removing and installing torque converter oil seal
  15
• Controls, housing
  17
• 1 Selector mechanism
  17
• 1.1 Assembly overview - selector mechanism
  17
• 1.2 Assembly overview - manual release mechanism for parking lock
  18
• 1.3 Checking selector mechanism
  19
• 1.4 Emergency release from position P
  23
• 1.5 Removing and installing selector lever handle
  24
• 1.6 Removing and installing selector mechanism
  25
• 1.7 Removing and installing emergency release cable for parking lock
  26
• 1.8 Renewing parking lock shaft seal
  30
• 2 Removing and installing gearbox
  33
• 2.1 Removing gearbox
  33
• 2.2 Installing gearbox
  37
• 2.3 Specified torques for gearbox
  43
• 3 Assembly mountings
  44
• 3.1 Assembly overview - assembly mountings
  44
• 3.2 Removing and installing tunnel cross member
  45
• 4 Transporting gearbox
  48
• 5 Securing to engine and gearbox support
  49
• 6 ATF circuit
  50
• 6.1 Assembly overview - ATF circuit
  50
• 6.2 Removing and installing ATF cooler
  52
• 6.3 Removing and installing ATF pipes
  54
• 7 ATF
  57
• 7.1 Checking ATF level
  57
• 7.2 Draining and filling ATF
  61
• Gears, control
  65
• 1 ATF system
  65
• 1.1 Assembly overview - ATF system
  65
• 1.2 Removing and installing sump
  66
• 1.3 Removing and installing auxiliary pump for gearbox oil
  68
• 2 Mechatronic unit
  73
• 2.1 Assembly overview - mechatronic unit
  73
• 2.2 Removing and installing mechatronic unit
  74
• Final drive - front differential
  83
• 1 Final drive
  83
• 1.1 Assembly overview - final drive
  83
• 1.2 Removing and installing O-ring on cover for front final drive
  85
• 2 Gear oil
  87
• 2.1 Checking gear oil level, gearbox with shared oil supply
  87
• 2.2 Draining and filling gear oil
  89
• 3 Oil seals
  93
• 3.1 Overview of fitting locations - seals
  93
• 3.2 Renewing left seal
  93
• 3.3 Renewing right oil seal
  96
• 4 Differential
  98
• 4.1 Removing and installing left flange shaft
  98
• 4.2 Removing and installing right flange shaft
  100
• 5 Self-locking centre differential
  103
• 5.1 Assembly overview - self-locking centre differential
  103
• 5.2 Removing and installing self-locking centre differential
  104
• 5.3 Removing and installing rear splined shaft
  105
• 5.4 Renewing seal for rear splined shaft
  108
• 5.5 Renewing ball bearing for rear splined shaft
  112
• 5.6 Renewing ball bearing for centre differential
  116
• 6 Transfer box
  119
• 6.1 Assembly overview - transfer box
  119
• 6.2 Dismantling and assembling transfer box
  120