Rear axle and rear final drive

Kapitelübersicht

• Technical data
  1
• 1 General information
  1
• 1.1 Rear axle type plate
  1
• 1.2 Advantages of all-wheel drive
  1
• 1.3 Function of permanent all-wheel drive
  1
• 1.4 Differential locks
  2
• 2 Repair notes
  3
• 2.1 Gaskets and seals
  3
• 2.2 Locking devices
  3
• 2.3 Nuts and bolts
  3
• 2.4 Bearings
  3
• 2.5 Shims
  4
• 3 Technical data
  5
• 3.1 Technical data for rear axle
  5
• 3.2 Technical data for transfer box
  15
• 3.3 Calculation of gear ratios
  15
• 4 Overview - power transmission
  16
• 4.1 Overview - power transmission - all-wheel drive
  16
• Controls, housing
  17
• 1 Transfer box (Crafter 4MOTION with Achleitner all-wheel drive)
  17
• 1.1 Assembly overview - transfer box
  17
• 1.2 Removing and installing transfer box
  18
• 1.3 Removing and installing rubber bush and rear bracket of transfer box
  21
• 1.4 Removing and installing upper bracket for transfer box
  23
• 1.5 Removing and installing rubber bush and front bracket for transfer box
  25
• 1.6 Removing and installing front bracket for transfer box
  26
• 1.7 Checking and replenishing gear oil level in transfer box
  27
• 1.8 Removing and installing transfer box control motor V455
  29
• 1.9 Removing and installing pneumatic actuator
  30
• Final drive - front differential
  32
• 1 Front final drive (Crafter 4MOTION with Achleitner all-wheel drive)
  32
• 1.1 Assembly overview - front final drive
  32
• 1.2 Removing and installing front final drive
  33
• 1.3 Checking and replenishing gear oil level in front final drive
  36
• 1.4 Removing and installing flange shafts on front final drive
  38
• 1.5 Renewing oil seals on front final drive
  39
• Final drive - differential
  41
• 1 Rear axle
  41
• 1.1 Assembly overview - rear axle
  41
• 1.2 Assembly overview - rear axle, Crafter 4MOTION with Achleitner four-wheel drive
  43
• 1.3 Removing and installing rear axle
  44
• 2 Gear oil
  56
• 2.1 Checking gear oil level
  56
• 2.2 Checking gear oil level, Crafter 4MOTION with Achleitner four-wheel drive
  57
• 3 Oil seals
  59
• 3.1 Renewing seal for propshaft flange of rear axle
  59
• 4 Final drive
  69
• 4.1 Assembly overview - final drive
  69
• 4.2 Adjustment overview
  74
• 4.3 Overview of shims
  75
• 4.4 Removing and installing drive pinion and differential
  78
• 4.5 Pulling tapered roller bearing for drive pinion off and pressing it on
  105
• 4.6 Pulling tapered roller bearing for differential off and pressing it on
  107
• 4.7 Adjusting crown wheel
  108
• 4.8 Tables for printing out, crown wheel adjustment
  111
• 4.9 Adjusting drive pinion
  112
• 4.10 Tables for printing out, drive pinion adjustment
  125
• 5 Propshaft
  126
• 5.1 Assembly overview - propshaft
  126
• 5.2 Assembly overview - propshaft, Crafter 4MOTION with Achleitner four-wheel drive
  134
• 5.4 Removing and installing propshaft
  137
• 5.5 Removing and installing front propshaft (Crafter 4MOTION with Achleitner all-wheel drive)
  139
• 5.6 Removing and installing rear propshaft (Crafter 4MOTION with Achleitner all-wheel drive)
  141
• 5.7 Aligning propshaft, Crafter 4MOTION with Achleitner four-wheel drive
  143
• 5.9 Renewing intermediate bearing of 2-part propshaft
  147
• 5.10 Renewing intermediate bearing of three section propshaft
  150
• 5.11 Renewing front intermediate bearing of propshaft
  157
• 5.12 Installing protective caps
  159
• 5.13 Removing and installing flexible coupling with damper weight
  161
• 5.14 Removing and installing damper weight
  165
• 6 Air compressor/pressure accumulator, Crafter 4MOTION with Achleitner four-wheel drive
  168
• 6.1 Assembly overview - air compressor V534 /pressure accumulator
  168
• 6.2 Removing and installing air compressor V534 and pressure accumulator
  170
• 6.3 Releasing pressure before working on compressed air system
  173
• 6.4 Repairing air line
  174
• 6.5 Removing and installing valve block for compressed air
  175
• 6.6 Removing and installing pressure switch for air compressor F503
  176
• 6.7 Performing pressure test
  177