Motronic injection and ignition system (2.8 ltr. engine, 4-valve)

Kapitelübersicht

• Self-diagnosis
  1
• 1 General to self-diagnosis
  1
• 1.1 General to self-diagnosis
  1
• 1.2 Features of self-diagnosis
  1
• 1.3 Significance of EPC warning lamp (fault lamp for electronic accelerator) in dash panel insert
  1
• 1.4 Significance of exhaust emissions warning lamp
  2
• 1.5 Technical data of self-diagnosis
  3
• 1.6 Connecting fault reader
  4
• 2 Fault memory
  7
• 2.1 Fault memory
  7
• 2.2 Interrogating and erasing fault memory
  7
• 3 Fault table: from V.A.G code 16396 / SAE P0 and P2 codes
  9
• 3.1 Fault table: from V.A.G code 16396 / SAE P0 and P2 codes
  9
• 4 Fault table: from V.A.G code 17463 / SAE P1 or P3 codes
  14
• 4.1 Fault table: from V.A.G code 17463 / SAE P1 or P3 codes
  14
• 5 Final control diagnosis
  22
• 5.1 Final control diagnosis
  22
• 5.2 Performing final control diagnosis
  22
• 6 Measured value blocks
  37
• 6.1 Measured value blocks
  37
• 6.2 Safety precautions
  37
• 6.3 Read measured value block
  37
• 7 Evaluating measured value blocks, display groups 0...6 -Basic functions-
  39
• 7.1 Evaluating measured value blocks, display groups 0...6 -Basic functions-
  39
• 8 Evaluating measured value blocks, display groups 10...29 -Ignition-
  42
• 8.1 Evaluating measured value blocks, display groups 10...29 -Ignition-
  42
• 9 Evaluating measured value blocks, display grps. 30...33, 99 -Lambda regulation-
  45
• 9.1 Evaluating measured value blocks, display grps. 30...33, 99 -Lambda regulation-
  45
• 10 Evaluating measured value blocks, display groups 50...69 -Speed regulation-
  50
• 10.1 Evaluating measured value blocks, display groups 50...69 -Speed regulation-
  50
• 12 Evaluating measured value block, display group 125 -Communication-
  55
• 12.1 Evaluating measured value block, display group 125 -Communication-
  55
• Mixture preparation, Injection
  57
• 1 Servicing injection system
  57
• 1.1 Servicing injection system
  57
• 1.2 Fitting locations overview
  57
• 1.3 General notes on injection
  64
• 1.4 Dismantling and assembling intake manifold
  65
• 1.5 Dismantling and assembling fuel distributor
  68
• 1.6 Dismantling and assembling air cleaner
  70
• 1.7 Safety precautions
  72
• 1.8 Rules for cleanliness
  74
• 1.9 Technical data
  74
• 2 Checking components
  75
• 2.1 Checking components
  75
• 2.2 Checking Lambda probe heating for Lambda probe before catalyst
  75
• 2.3 Checking Lambda probe heating for Lambda probe after catalyst
  78
• 2.4 Checking air mass meter
  81
• 2.5 Checking throttle valve control part
  84
• 2.6 Checking coolant temperature sender
  88
• 2.7 Checking intake air temperature sender
  93
• 2.8 Checking engine speed sender
  98
• 2.9 Checking injectors
  99
• 2.10 Checking fuel pressure regulator and holding pressure
  106
• 2.11 Checking intake manifold change-over
  109
• 2.12 Checking intake air system for leaks (unmetered air)
  110
• 3 Checking functions
  112
• 3.1 Checking functions
  112
• 3.2 Idling check
  112
• 3.3 Adapting idling speed
  113
• 3.4 Checking Lambda probe and Lambda regulation before catalyst
  115
• 3.5 Checking Lambda probe and Lambda regulation after catalyst
  118
• 3.6 Checking Lambda probe ageing of Lambda probe before catalyst
  121
• 3.7 Checking Lambda probe ageing Lambda probe after catalyst (adaption)
  122
• 3.8 Checking engine operating mode
  123
• 4 Engine control unit
  124
• 4.1 Engine control unit
  124
• 4.2 Checking control unit voltage supply
  124
• 4.3 Procedure after voltage supply open circuit
  126
• 4.4 Erasing values learnt by engine electronics control unit
  127
• 4.5 Replacing engine control unit
  128
• 4.6 Coding engine control unit
  129
• 4.7 Adapting engine control unit to throttle valve control part
  130
• 4.8 Learning kick-down point
  131
• 5 Checking additional signals
  132
• 5.1 Checking additional signals
  132
• 5.2 Checking speed signal
  132
• 5.3 Checking signal from/to air conditioner
  134
• 5.4 Checking signal from brake light switch and brake pedal switch
  136
• 5.5 Checking cruise control system (CCS)
  139
• 5.6 Checking matching resistor of data bus
  141
• Ignition system
  142
• 1 Servicing ignition system
  142
• 1.1 Servicing ignition system
  142
• 1.2 General notes on ignition system
  142
• 1.3 Removing and installing parts of the ignition system
  143
• 1.4 Safety precautions
  147
• 1.5 Test data, spark plugs
  148
• 1.6 Checking Hall sender
  149
• 1.7 Checking ignition coils with output stage
  152
• 1.8 Checking knock sensor
  154
• 1.9 Check misfire recognition
  158